OE-style intake manifold gasket designed to seal the intake manifold to the cylinder head during installation or service.
$5.87
The 058 129 717D intake manifold gasket seals the connection between the intake manifold and cylinder head. It helps keep the intake tract properly sealed so the engine receives the air measured by its management system.
Over time, heat cycles and repeated manifold removal can compress or damage the gasket material. Replacing the gasket whenever the intake manifold is removed helps prevent unmetered-air leaks and supports consistent engine operation.
A secure intake-manifold seal is important for maintaining the intended air-fuel mixture. When the gasket leaks, extra air can enter after the airflow measurement point. This can cause the engine control system to make unwanted fuel corrections, potentially affecting idle quality, fuel economy, emissions, and overall performance.
Installing a new gasket during intake-manifold service is a practical preventive-maintenance step. It helps restore the correct sealing surface and avoids reusing a compressed or deteriorated gasket.
Inspect the intake-manifold sealing area if you notice:
Rough, unstable, or elevated idle speed.
Hissing sounds around the intake manifold.
Check-engine light with lean-mixture or intake-air leak faults.
Reduced acceleration or inconsistent engine response.
Increased fuel consumption.
Failed emissions testing or readiness concerns.
Visible gasket damage during intake-manifold removal.
Similar symptoms may result from damaged vacuum lines, intake hoses, or other engine-management faults. Diagnose the entire intake system before replacing components.
OE Part Number: 058 129 717 D
Function: Seals the intake manifold to the cylinder head.
Application: Small-port 1.8T intake-manifold configuration.
Direct Replacement: Designed for the corresponding original-equipment sealing surface.
Service Recommendation: Replace whenever the intake manifold is removed.
OE-Style Fit: Supports correct manifold installation and intake-system sealing.
Always verify fitment by VIN before ordering.
058 129 717 D
058129717D
058-129-717-D
058.129.717.D
Elring 476.460
| Weight | .1 lbs |
|---|---|
| Dimensions | 12 × 4 × .2 in |
| Mfg Part # | 058129717D |
| Year | Make | Model | Engine | Notes |
|---|---|---|---|---|
| 1997-2006 | Audi | A4 | 1.8L | |
| 2000-2006 | Audi | TT | 1.8L | |
| 1999-2005 | Volkswagen | Beetle | 1.8L | |
| 2000-2006 | Volkswagen | GTI | 1.8L | |
| 2000-2005 | Volkswagen | Jetta | 1.8L | |
| 1998-2005 | Volkswagen | Passat | 1.8L |
The 11 28 8 673 720 is an INA (Schaeffler) OEM-quality accessory belt deflection/idler pulley for BMW N55 TwinPower Turbo and S55 Twin Turbo engines across the F-series lineup — including the 3 Series, 4 Series, 5 Series, X3, X5, M3, and M4. This pulley guides the serpentine belt around the accessory drive and delivers quiet, stable belt tracking through a precision sealed bearing — with no modifications required.
The 06H 121 119E thermostat housing o-ring is a factory Genuine OEM seal designed to provide a pressure-tight connection between the thermostat housing and the engine.
—Genuine 03L133821 Grommet (EGR Tube Adapter) designed for Volkswagen and Audi models. Restores the airtight seal between the EGR tube and intake for optimal engine efficiency.
OEM-quality 03H121041B Coolant Pipe Gasket for select Volkswagen and Audi models. Provides a reliable seal for the rear water pipe to protect your engine from overheating.
OEM-quality oil filter, OE number 021 115 562 A. Removes engine contaminants to protect internal components at every oil change interval.
