ECU-controlled EVAP purge valve that regulates fuel-vapor flow from the charcoal canister to the engine intake.
$47.99
The 058 133 517 purge valve is an ECU-controlled component in the evaporative-emissions system. It regulates the flow of stored fuel vapors from the charcoal canister into the engine, where the vapors are burned during normal operation.
By opening and closing at the correct time, the valve helps the engine management system control fuel vapor recovery and monitor the EVAP system for leaks. A failed valve can interrupt vapor flow, trigger a check-engine light, and contribute to driveability concerns.
Fuel vapors naturally develop inside the fuel tank. Rather than releasing them into the atmosphere, the EVAP system stores these vapors in a charcoal canister. The engine control unit then commands the valve to open when operating conditions allow the engine to burn the vapors.
The 058 133 517 purge valve also supports EVAP self-testing. During certain diagnostic routines, the valve must close so the control unit can assess whether the system holds pressure or vacuum as intended. Correct valve operation helps maintain emissions-system performance and accurate fault monitoring.
A faulty valve may cause one or more of the following symptoms:
Check-engine light with EVAP-related diagnostic trouble codes.
Diagnostic trouble code P0441, which may indicate an incorrect purge-flow condition.
Rough idle or inconsistent engine operation.
Hard starting after refueling.
Fuel-vapor odor near the vehicle.
Failed emissions-system readiness or inspection testing.
Clicking, sticking, or no response during commanded diagnostic testing.
Always diagnose the EVAP system fully before replacing components, as damaged hoses, wiring faults, or a defective charcoal canister can produce similar codes.
OE Part Number: 058 133 517
Function: Controls vapor flow from the charcoal canister to the engine intake.
ECU-Controlled: Opens and closes in response to engine-management commands.
EVAP System Support: Assists vapor recovery and onboard leak-detection testing.
Direct Replacement: Designed to replace the corresponding original purge-control valve.
Cross Reference: Bosch 0 280 142 300 / 0280142300.
Always verify fitment by VIN before ordering.
058 133 517
| Weight | .25 lbs |
|---|---|
| Dimensions | 4 × 3 × 2.5 in |
| Mfg Part # | 058133517 |
| Year | Make | Model | Engine | Notes |
|---|---|---|---|---|
| 1997-2000 | Audi | A4 | 1.8L | |
| 1995-1998 | Volkswagen | Golf | 2.8L V6 | |
| 1994-1996 | Volkswagen | Jetta | 2.8L V6 | |
| 1998-2000 | Volkswagen | Passat | 1.8L | |
| Audi | B5 A4 | 1.8T | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf III | VR6 12v | For vehicles with VIN from 1H-S-007 947 through VIN 1H-S-999 000 only, split is in the 1995 model year | |
| Volkswagen | Jetta III | VR6 12v | For vehicles with VIN from 1H-S-007 947 through VIN 1H-S-999 000 only, split is in the 1995 model year | |
| Volkswagen | Passat B5 | 1.8T | Use vehicle selector to confirm fitment |
The 07K 145 172C is a Metrix OE-style lower accessory drive belt idler pulley for select Volkswagen and Audi 2.5L 5-cylinder applications. Engineered to OE dimensions with a sealed bearing, this direct-fit pulley restores correct belt alignment and smooth, quiet accessory drive operation — no modifications required.
The 021 103 601B pan is a stamped-steel, OE-style replacement oil sump for select Volkswagen VR6 engines. It restores proper oil containment and lower-engine protection.
Replacement valve cover gasket for 24v VR6 engines. Designed to stop oil leaks and protect your valvetrain in 2.8L and 3.2L applications.
032121142 Sensor Clip is an OEM-style coolant temperature sensor retainer that supports correct sensor seating and leak-free sealing.
Victor Reinz OEM-quality thermostat housing O-ring, OE number 021 121 119 A. Prevents coolant leaks at the thermostat housing and engine block connection.
