Direct-fit distributor cap for compatible Volkswagen ignition systems. Helps restore reliable spark routing and smoother engine operation.
$20.00
The 051 905 207 distributor cap directs ignition voltage from the distributor rotor to the appropriate spark-plug wire. This sequence allows each cylinder to receive spark at the required point in the ignition cycle.
The cap is an important insulating and electrical-routing component in distributor-equipped engines. Its internal terminals must remain clean and intact to transfer ignition energy consistently. Age, engine-bay heat, vibration, moisture, and repeated electrical arcing can wear the cap over time.
A distributor cap in poor condition can disrupt the path of ignition voltage. Cracks in the housing, corrosion at the terminals, or carbon tracking inside the cap may cause the spark to travel incorrectly or weaken before reaching the spark plugs.
Replacing a worn cap supports stable combustion and dependable engine operation. Routine ignition-system service can also help identify related components that need attention before performance concerns become more severe.
Inspect the distributor cap if you notice:
Rough, uneven, or unstable idle.
Misfires during acceleration or under load.
Extended cranking or difficult starting.
Hesitation and reduced throttle response.
Reduced fuel economy.
Visible cracks on the cap housing.
Corroded, burned, or carbon-tracked internal terminals.
OE Part Number: 051 905 207
Function: Routes distributor output to the correct spark-plug wire.
Fitment Type: Direct replacement for compatible Volkswagen distributor ignition systems.
Construction: Designed for normal ignition-system voltage, heat, and vibration exposure.
Service Purpose: Replaces a damaged, worn, or electrically compromised distributor cap.
Installation: Fits in the original distributor-cap location on applicable engines.
Always verify fitment by VIN before ordering. Service the ignition system with the engine switched off and cool. Before removing the existing cap, label each spark-plug wire or transfer one wire at a time to preserve the firing order.
051 905 207
| Weight | .40 lbs |
|---|---|
| Dimensions | 4.5 × 4.5 × 3.5 in |
| Mfg Part # | 051905207 |
| Year | Make | Model | Engine | Notes |
|---|---|---|---|---|
| 1995-2002 | Volkswagen | Cabrio | 2.0L | |
| 1990-1998 | Volkswagen | Golf | 1.8L | |
| 1990-1998 | Volkswagen | Golf | 2.0L | |
| 1990-1998 | Volkswagen | Jetta | 1.8T | |
| 1990-1998 | Volkswagen | Jetta | 2.0L | |
| 1993-1996 | Volkswagen | Passat | 2.0L | |
| Volkswagen | Cabrio III | 2.0 | Use vehicle selector to confirm fitment | |
| Volkswagen | Corrado | G60 | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf I | 8v | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf II | 16v | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf II | 8v | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf III | 2.0 | Use vehicle selector to confirm fitment | |
| Volkswagen | Golf IV | 2.0 | Use vehicle selector to confirm fitment | |
| Volkswagen | Jetta II | 16v | Use vehicle selector to confirm fitment | |
| Volkswagen | Jetta II | 8v | Use vehicle selector to confirm fitment | |
| Volkswagen | Jetta II | Diesel | Use vehicle selector to confirm fitment | |
| Volkswagen | Jetta III | 2.0 | Use vehicle selector to confirm fitment | |
| Volkswagen | Jetta IV | 2.0 | Use vehicle selector to confirm fitment | |
| Volkswagen | Passat B3 | 16v | Use vehicle selector to confirm fitment | |
| Volkswagen | Passat B4 | 2.0 | Use vehicle selector to confirm fitment |
The ABS Speed Sensor WHT003860 is a genuine-spec, OE-quality replacement for select Volkswagen and Audi models. It delivers precise wheel-speed data to your ABS, ESP, and traction control systems with a direct plug-and-play installation and no modifications required.
The ABS Speed Sensor WHT003857A is a genuine-spec, direct-fit replacement for select Audi and Volkswagen models. It delivers accurate wheel-speed data to ABS, ESP, and traction control systems — restoring full safety-system performance with a simple plug-and-play installation.
The 4H0 121 671D heater valve by HEPU is a genuine‑spec replacement that precisely meters coolant flow to the heater core for consistent and reliable cabin temperature control.
OEM-quality MAP sensor, OE number 036 906 051 G. Provides accurate intake pressure data for ECU engine management and efficiency.
